3300 XL 11mm Probe | Model 330707-00-25-10-01-05 by Bently Nevada

Product HighlightsOriginal Bently Nevada 3300 XL 11mm Proximity Probe, made in the USA.Standard 5/8-18 UNF threaded case for secure mounting.Includes a 1-meter (3.3 ft) cable with a secure Miniature ClickLoc connector.Wide operating temperature range from -51°C to 177°C (-60°F to 351°F).Robust construction with a PPS probe tip and 304 stainless steel case.Essential for predictive maintenance on rotating machinery.Part Number ConfigurationBase Model: 330707 (3300 XL 11mm Probe)Diameter: 11 mmOption Codes: -00-25-10-01-0500: Unthreaded Length = 0.0 in25: Overall Case Length = 2.5 in10: Total Cable Length = 1.0 metre01: Miniature Coaxial ClickLoc Connector05: Multiple Agency ApprovalsComplete Technical DataManufacturer & P/N: Bently Nevada 330707-00-25-10-01-05Probe Type: Non-contact Eddy Current ProximityProbe Diameter: 11 mmCase Thread: 5/8-18 UNFCase Material: AISI 304 Stainless SteelProbe Tip Material: Polyphenylene Sulfide (PPS)Cable Type & Length: 75 Ω Triaxial, FEP Insulated, 1.0 metreConnector: Miniature Coaxial ClickLoc with protectorDC Probe Resistance: 5.9 Ω ± 0.5 ΩTemperature Range: -51°C to 177°C (Operating & Storage)Maximum Thread Engagement: 0.938 in (23.8 mm)Recommended Case Torque: 15.2 N•m (133 in•lb)Maximum Case Torque: 45.2 N•m (400 in•lb)Minimum Cable Bend Radius: 25.4 mm (1.0 in)Shipping Weight: Approximately 0.17 kgInstallation NotesClean the mounting hole before installation.Use the recommended torque (15.2 N•m) on the probe case.Do not exceed the maximum torque to avoid damage.Ensure the cable is not bent tighter than a 1-inch radius.Connect the ClickLoc connector finger-tight; do not over-torque.Common ApplicationsShaft vibration monitoring in gas and steam turbines.Radial and axial position measurement in compressors.Keyphasor® timing reference applications.General machinery protection and condition monitoring.FAQ & Expert TipsWhat is the ClickLoc connector?It is a Bently Nevada proprietary quick-connect connector. It locks securely and ensures proper electrical contact. A connector protector is included.Can this probe be used in high-pressure environments?The probe has a Viton O-ring seal. It is not pressure-tested before shipping. For high-pressure applications, consult Bently Nevada’s custom design department.Why is the cable impedance 75 ohms?The 75-ohm triaxial cable is matched to the probe and monitor system. Using the correct cable is critical for accurate signal transmission.What happens if I install the probe below -34°C?Exposure to very low temperatures may damage the pressure seal (O-ring), causing premature failure. Keep probes within the specified storage range.How do I select the correct probe length and cable?The model 330707-00-25-10-01-05 specifies a 2.5″ case and 1m cable. Choose based on your mounting depth and distance to the monitor. Other lengths (5m, 9m) are available with different option codes.Ordering & SupportCondition: New Original, Made in USA.Shipping: Global express via FedEx, UPS, DHL.Warranty: Full 12-month warranty on manufacturer defects.Technical Support: Contact [email protected] or WhatsApp: 86 158 8020 0923.Copyright © 2026 Oiltech Controls Limited. All rights reserved.Original Source: https://www.oiltechcontrols.com/Partner PLCDCS HUB Limited https://plcdcshub.com/. All rights reserved.Powergear X Automation Limited https://www.powergearx.com/